Steel Mills
USS to Indefinitely Idle No. 3 Blast Furnace at Edgar Thomson
Written by Michael Cowden
September 26, 2022
US Steel has decided to indefinitely idle the No. 3 blast furnace at its Mon Valley Works in western Pennsylvania following a roughly month-long maintenance outage.
“We expect planned maintenance on BF 3 to be completed and the furnace to be available for use this week. However, the furnace will remain down until market conditions improve,” a company spokeswoman said in an email to SMU on Monday, Sept. 26.
The statement was later revised to say the furnace would stay down “as we continue to balance our production with our order book.”
There are no layoffs associated with the idling, she added.
The Pittsburgh-based steelmaker took the No. 3 furnace offline on Aug. 30 for a shotcrete (sprayed concrete) reline and other maintenance. The outage had been pulled forward by more than a month. Sources had told SMU that the furnace was likely to remain idle after the work was complete.
That pattern – pulling forward maintenance first and then idling a plant – is not uncommon in a deteriorating steel market.
Mon Valley Works has two blast furnaces: No. 1 and No. 3. The No. 1 furnace has a daily ironmaking capacity of approximately 3,200 tons. The No. 3 furnace has a daily capacity of approximately 2,900 tons.
The furnaces are located at US Steel’s Edgar Thomson plant in Braddock, Pa. That facility makes slabs and rails them to the company’s Irvin Plant in West Mifflin, Pa., where they are rolled into sheet.
SMU has updated its blast furnace status table to reflect the idling of No. 3.
The idling means that US Steel is only operating one furnace each at its Mon Valley Works and at its Granite City Works near St. Louis. The company also announced earlier this month that it was idling the No. 8 furnace at its Gary Works in northwest Indiana. The result: US Steel is operating only five of its eight active blast furnaces.
The idlings at US Steel come after Cleveland-Cliffs Inc. restarted the C-5 furnace at its Cleveland Works in Ohio in August. The Cleveland-based steelmaker currently has seven furnaces operating – meaning there are now only a dozen active blast furnace in the US.
By Michael Cowden, Michael@SteelMarketUpdate.com, and David Schollaert, David@SteelMarketUpdate.com
Michael Cowden
Read more from Michael CowdenLatest in Steel Mills
Mexico’s TYASA breaks ground on SBQ rolling mill
Mexican steelmaker Talleres y Aceros (TYASA) broke ground this month on the construction of a new special bar quality (SBQ) rolling mill in the state of Veracruz.
Goncalves sees more US trade actions ahead, says Nippon deal for USS has ‘zero chance’
Cleveland-Cliffs’ Lourenco Goncalves thinks trade measures announced by the US government on Tuesday against China were just the opening salvo in a series of trade actions. Case in point: The Biden administration targeted China’s “unfair” trade policies with additional tariffs on an array of Chinese-made goods - including steel, aluminum, and EVs.
Nucor holds weekly HRC price steady after last week’s cut
Nucor chose to hold its consumer spot price (CSP) for hot-rolled (HR) coil steady this week after stunning the market last week with a significant price decline. The steelmaker said in a letter to customers on Monday morning that its $760-per-short-ton (st) CSP base price for HR coil is effective immediately. The price is unchanged from the CSP announced on May 6 but down $65/st from $825/st April 29.
Nucor’s Jellison set to retire, Spicer tapped for EVP role
Nucor said EVP Douglas J. Jellison plans to retire on June 8 after more than 33 years with the company. Randy J. Spicer will be promoted to EVP effective May 12.
Republican Senators demand Biden block USS sale to Nippon
Three vocal Republican senators are demanding that President Joe Biden block the sale of U.S. Steel to Japan’s Nippon Steel.