Steel Mills
USS to Indefinitely Idle No. 3 Blast Furnace at Edgar Thomson
Written by Michael Cowden
September 26, 2022
US Steel has decided to indefinitely idle the No. 3 blast furnace at its Mon Valley Works in western Pennsylvania following a roughly month-long maintenance outage.
“We expect planned maintenance on BF 3 to be completed and the furnace to be available for use this week. However, the furnace will remain down until market conditions improve,” a company spokeswoman said in an email to SMU on Monday, Sept. 26.
The statement was later revised to say the furnace would stay down “as we continue to balance our production with our order book.”
There are no layoffs associated with the idling, she added.
The Pittsburgh-based steelmaker took the No. 3 furnace offline on Aug. 30 for a shotcrete (sprayed concrete) reline and other maintenance. The outage had been pulled forward by more than a month. Sources had told SMU that the furnace was likely to remain idle after the work was complete.
That pattern – pulling forward maintenance first and then idling a plant – is not uncommon in a deteriorating steel market.
Mon Valley Works has two blast furnaces: No. 1 and No. 3. The No. 1 furnace has a daily ironmaking capacity of approximately 3,200 tons. The No. 3 furnace has a daily capacity of approximately 2,900 tons.
The furnaces are located at US Steel’s Edgar Thomson plant in Braddock, Pa. That facility makes slabs and rails them to the company’s Irvin Plant in West Mifflin, Pa., where they are rolled into sheet.
SMU has updated its blast furnace status table to reflect the idling of No. 3.
The idling means that US Steel is only operating one furnace each at its Mon Valley Works and at its Granite City Works near St. Louis. The company also announced earlier this month that it was idling the No. 8 furnace at its Gary Works in northwest Indiana. The result: US Steel is operating only five of its eight active blast furnaces.
The idlings at US Steel come after Cleveland-Cliffs Inc. restarted the C-5 furnace at its Cleveland Works in Ohio in August. The Cleveland-based steelmaker currently has seven furnaces operating – meaning there are now only a dozen active blast furnace in the US.
By Michael Cowden, Michael@SteelMarketUpdate.com, and David Schollaert, David@SteelMarketUpdate.com
Michael Cowden
Read more from Michael CowdenLatest in Steel Mills
Nucor breaks ground on new Berkeley galv line
Nucor broke ground on a new galvanizing line at its Nucor Steel Berkeley sheet mill in Huger, S.C., on Thursday, May 2.
USS, Nippon merger delayed by DOJ antitrust review
The sale of U.S. Steel Corp. to Nippon Steel Corp. has been delayed by the US Department of Justice’s antitrust investigation. The Justice Department, which is conducting an antitrust review of the merger, has requested additional information from both USS and NSC. The companies originally anticipated closing the sale in the second or third quarter […]
U.S. Steel Q1 earnings slip, BRS expansions proceed
U.S. Steel posted slightly lower Q1’24 earnings as stronger earnings from its sheet mills were partially offset by a weaker performance from it tubular division. All told, the Pittsburgh-based steelmaker reported Q1’24 earnings of $171 million. That's down 14.1% from $199 million in Q1’23 on sales that fell 6.9% to $4.16 billion in the same comparison.
ArcelorMittal says Calvert CR outage over, floats buying Nippon’s stake in JV
ArcelorMittal posted a narrower Q1’24 profit compared to Q1’23 but remained optimistic about steel's long-term demand prospects.
SMU Community Chat: Hybar’s ambitious plans as newest player in rebar
Hybar has big plans for entering the American steel market. Although it is the newest player in the US rebar market, the startup is led by an experienced, nimble, and ambitious team, and backed by investors with deep pockets. Industry titan and Hybar CEO David Stickler joined SMU Managing Editor Michael Cowden on Wednesday’s Community Chat to update the SMU community on the company’s first mill, and its grand plans for the future.