Steel Products Prices North America
SIMA: Steel Import License Data for June
Written by Peter Wright
July 12, 2019
Total rolled product imports in June were down by 20.5 percent on a three-month moving average (3MMA) basis year over year. This follows the 27.4 percent decline in May on the same basis.
This early look at June’s import volume is based on Commerce Department license data (see explanation below.) This import analysis includes all major steel sectors: sheet, plate, longs and tubulars, with a total of 18 subsectors. We now publish an import market share analysis for the same 18 steel product groups. All volumes in this analysis are reported in short tons. We use three-month moving averages rather than single-month results to smooth out monthly variability.
Imports of total rolled products were down in April, May and June on a 3MMA basis, but in the 11 months August 2018 through June 2019 have been consistently in the range of 1.79 million to 1.94 million tons. In June, the 3MMA was 1.821 million tons, therefore at the bottom of the range. This consistency is not apparent in the year-over-year analysis because in the period December 2017 through July 2018, the range was much higher at 1.98 million to 2.49 million tons. Year over year on a 3MMA basis, sheet products were down by 23.5 percent, plate products were down by 26.0 percent, long products were down by 15.1 percent and tubulars were down by 20.5 percent. This is an example of how a report can spin very different conclusions based on the chosen time period of reference. Imports of flat rolled, tubulars and longs all had a recent peak in June last year. Since then total flat rolled (sheet + plate) imports have consistently declined, which may be tariff-driven. This is not so clear for longs and tubulars where the decline since June has been less consistent.
Figure 1 shows the tonnage of total rolled steel and semi-finished imports through June on a 3MMA basis. Total rolled product volume has been on an erratically downward trend since mid-2017. Imports of semi-finished have been very erratic on a monthly basis since last August with a high of 1,280,000 tons in April this year, a low of 197,803 tons in May this year and a recovery to 870,589 in June. This is why we use a 3MMA calculation in our analyses, the result of which is the much smoother line for semis in Figure 1. On this basis since January last year, the range has been 492,000 to 884,000 tons with June at the high end with 783,000 tons. Evidently the Section 232 legislation has had no effect on semi-finished products.
Figure 2 summarizes the import volume of flat rolled, tubular and long products since 2004 on a 3MMA basis. All three have been trending down, but tubulars and longs have experienced a minor increase since December.
There are three tables in this report. In each of them we show the 3MMA of the tonnage in June 2019 and June 2018 with the year-over-year change. We then calculate the percentage change in volume in the most recent three months with the previous three months. This month we are comparing April through June with January through March (3M/3M). The next column to the right shows the year-over-year change as a percentage. Declines are color coded green and increases are coded red. Finally, in the far-right column, we subtract the 12-month change from the three-month change. This is a way of describing the magnitude of the recent trend as a percentage. It is not unusual for the color code of the trend to be the opposite of the two time frame analyses.
Table 1 describes the imports of all major sectors of the sheet and plate markets. In the flat rolled sectors shown in Table 1, total sheet and total plate products were down by over 20 percent year over year. On an individual product basis, only electrogalvanized and tin plate were up year over year. Every product except CTL plate had a trend of increasing imports when comparing Y/Y with 3M/3M. Figures 3 and 4 show the history of sheet and plate product imports since June 2004.
Table 2 shows the same analysis for long products where the year-over-year volume was down by 20.5 percent in total. All products except wire rod were down by over 14 percent. Figure 5 shows the history of long product imports.
Table 3 shows that for tubular products in total the volume was down by 20.5 percent year-over-year with structural tubing down the most and OCTG down the least. Figure 6 shows the history of tubular imports since 2004.
Explanation: SMU publishes several import reports ranging from this very early look using license data to the very detailed analysis of final volumes by product, by district of entry and by source nation, which is available in the premium member section of our website. The early look is based on three-month moving averages using the latest license data, either the preliminary or final data for the previous month and final data for earlier months. We recognize that the license data is subject to revisions but believe that by combining it with earlier months in this way gives a reasonably accurate assessment of volume trends by product as early as possible. The main issue with the license data is that the month the tonnage arrives is not always the same month in which the license was recorded. In 2014, we conducted a 12-month analysis to evaluate the accuracy of the license data compared to final receipts. This analysis showed that the licensed tonnage of all carbon and low alloy products was 2.3 percent less than actual receipts, close enough to confidently include license data in this current update. The discrepancy declined continuously during the 12-month evaluation as a longer period was considered.
Statement from the Department of Commerce: The Steel Import Monitoring and Analysis (SIMA) system of the Department of Commerce collects and publishes data of steel mill product imports. By design, this information gives stakeholders valuable information on steel trade with the United States. This is achieved through two tools: the steel licensing program and the steel import monitor. All steel mill imports into the United States require a license issued by the SIMA office. The SIMA Licensing System is an online system for importers to register, apply for and receive licenses in a timely manner. In addition to managing the licensing system, SIMA publishes near-real-time aggregate data on steel mill imports into the United States. These data incorporate information collected from steel license applications and publicly released Census data. The data are displayed in tables and graphs for users to analyze. Additionally, SIMA provides data on U.S. steel mill exports, as well as imports and exports of select downstream steel products.
Peter Wright
Read more from Peter WrightLatest in Steel Products Prices North America
CRU: US longs prices remain mostly flat in October
CRU Senior Steel Analyst Alexandra Anderson shares insight into the current market for long steel products.
Nucor holds HR base price at $730/st
Nucor is holding its hot-rolled (HR) coil consumer spot price (CSP) at $730 per short ton (st) this week.
Buyers say galv prices stable mill level but stuck in swamp on the street
Galvanized steel buyers on Tuesday discussed the eerie stability in sheet prices of late. Expectations are for the murky market to persist in the short term, while glimmers of hope continue for prices pushing higher.
Nucor ups weekly HR price by $10/ton
Nucor’s weekly consumer spot price (CSP) for hot-rolled (HR) coil increased $10 per short ton (st) from last week to $730/st as of Monday, Sept. 23.
Plate report: Prices getting closer to pre-Covid norms
The US plate market finds itself in unfamiliar territory, well maybe unfamiliar territory for this side of the post-Covid “normal,” that is.