Flat rolled steel prices continued their slow slide as hot rolled offers below $600 per ton became commonplace. We have also seen lead times shrinking, demand in question and service center inventories grow. The combination of these and other factors caused SMU to adjust our Price Momentum Indicator to Lower from Neutral where it had […]
For the week ending August 13, 2016, the American Iron & Steel Institute (AISI) estimated the U.S. steel industry produced 1,685,000 net tons of raw steel, a 0.7 percent decrease over the previous week and a 2.4 percent decrease over the same week one year ago. The estimated capacity utilization rate is 72.1 percent, down […]
Foreign steel imports are trending toward once again coming in above both the 3 month and 12 month moving average. The U.S. Department of Commerce released license data earlier today and, based on that information, we are on pace for a 2.8 million ton (net tons) month. This would be lower than the 3.2 million […]
Flat rolled steel prices slipped across the board this past week as the domestic steel mills became more aggressive in order to finish filling their August order books (hot rolled) as well as September (cold rolled and coated). For the first time in many months, Steel Market Update adjusted our hot rolled and cold rolled […]
The following report on steel exports is from the American Institute for International Steel (AIIS): Falls Church, VA. August 10, 2016. Steel exports crept up 1 percent from May to June, reaching 811,211 net tons. The June total was down 8.4 percent from a year earlier, however. Exports to Canada were nearly unchanged month-to-month at […]
The SMU monthly import analysis describes the total tonnage by product. It is intended to be a big picture commentary that describes how import volumes are changing and by implication what effect they are having on the macro market. It does not provide any regional information nor does it tell us the country of origin. […]
Steel Market Update is reintroducing our monthly analysis of foreign steel imports into the United States by product, port and country. This report will be available to our Premium level members shortly after the U.S. government releases the Final Census data for each month. The data was just released for the month of June. Since […]
A steel mill told SMU this afternoon, “The week has definitely taken a turn south.” Over the past twenty-four hours a couple of the domestic steel mills have moved their base spot number on hot rolled to $570 to $590 per ton ($28.50/cwt to $29.50/cwt). We are receiving mixed messages regarding whether there are specific […]
The following calculation is used by Steel Market Update to identify the spread between foreign hot rolled export prices and domestic hot rolled prices. We want our readers to note that we have made a decision to replace SteelBenchmarker as the primary data provider of foreign hot rolled coil prices. We were finding the comparison […]
The following article on the hot rolled coil (HRC) and financial futures markets was written by Jack Marshall of Crunch Risk LLC. Here is how Jack saw trading over the past week: Steel HR futures prices are down over $10/ST Sep’16/Dec’17 over the last week, roughly in line with the different indexes being reported. SMU […]
According to the latest data released from the U.S. Department of Commerce and the American Iron and Steel Institute, apparent steel supply for the month of June 2016 was 9,098,316 net tons. Apparent steel supply is calculated by adding domestic steel shipments and finished US steel imports, then subtracting total US steel exports. June apparent […]
The hot rolled announcement has been made and the market is sifting through the results in order to figure out whether the results are good or bad for the steel industry. Of course, the answer to that question depends on what your end motivation is. Lower prices are good for manufacturing but bad for the […]
As we moved about the market speaking to buyers of flat rolled steel, we found ourselves immersed in a dialogue about demand now being the major driver of steel prices moving forward. SMU spoke with a number of very large flat rolled steel service center buyers who told us that demand is “fragmented” and there […]
The U.S. Department of Commerce released Final Census Data for June as well as an update on July import license data earlier this week. Foreign steel imports came in at 2,821,894 net tons during the month of June. This is essentially unchanged from the prior month’s 2,876,358 net tons of imports. July imports, based on […]
For the week ending August 6, 2016, the American Iron & Steel Institute (AISI) estimated the U.S. steel industry produced 1,697,000 net tons of raw steel, a 1.0 percent increase over the previous week but a 1.7 percent decrease over the same week one year ago. The estimated capacity utilization rate is 72.6 percent, up […]
We saw minor erosion in hot rolled prices this past week according to the steel indexes followed by Steel Market Update. Both our own index as well as Platts dropped their HRC average by $5 per ton. As of the end of last week Steel Market Update was showing hot rolled as averaging $610 per […]
SMU Sources are advising us that obsolete grades of ferrous scrap are trading sideways (prices remaining the same as last month) while prime grades move lower by $10 to $15 per gross ton in the Chicago, Ohio Valley, Detroit and Indiana markets. Prior to negotiations beginning, the expectation was for obsolete grades to remain intact […]
The following article on the hot rolled coil (HRC), busheling scrap (BUS), and financial futures markets was written by David Feldstein. As Flack Steel’s director of risk management, Dave is an active participant in the hot rolled coil (HRC) futures market and we believe he will provide insightful commentary and trading ideas to our readers. […]
A couple of the steel mills SMU spoke with today reported their coated order books as being close to closed for September. They reported that there is not a need to make any price adjustments. At the same time, both the mills we spoke with, as well as steel buyers around the country, are anxiously […]
By the end of this week, the U.S. Department of Commerce is scheduled to release their final determinations on hot rolled antidumping and countervailing duties against seven countries: Brazil, South Korea, Australia, Japan, United Kingdom, Turkey and the Netherlands. Combined these seven countries represented roughly 55 percent of all hot rolled imported into the United […]
For the week ending July 30, 2016, the American Iron & Steel Institute (AISI) estimated the U.S. steel industry produced 1,681,000 net tons of raw steel, a 1.3 percent decrease over the previous week and a 3.9 percent decrease over the same week one year ago. The estimated capacity utilization rate is 71.9 percent, down […]
The American Iron & Steel Institute (AISI) recently reported final U.S. raw steel production estimates for the month of June 2016. The monthly estimates are different than the weekly estimates we report in our Tuesday issues; the AISI bases the monthly estimates on over 75 percent of the domestic mills reporting vs. only 50 percent […]
The following calculation is used by Steel Market Update to identify the spread between European and Chinese hot rolled export prices and domestic (US) hot rolled prices. We want our readers to note that we have made a decision to replace SteelBenchmarker as the primary data provider of world and Chinese hot rolled coil pricing. […]
Flat rolled steel prices are relatively stable for yet another week according to the various steel indexes followed by Steel Market Update. SMU took two items slightly lower: cold rolled ($815/ton) and Galvanized .060” G90 ($880/ton). SteelBenchmarker, who only reports prices twice per month, saw hot rolled down $4/ton ($624/ton) and cold rolled was off […]
The following article on the hot rolled coil (HRC) and financial futures markets was written by Jack Marshall of Crunch Risk LLC. Here is how Jack saw trading over the past week: Steel A trickle of bullish news for steel helping to push values higher on very light HR futures volume and reduced selling interests. […]
Cliffs Natural Resources recorded another successful quarter with net income of $30 million for continuing operations compared to a net loss of $38 million in Q2 2015. Adjusted EBITDA was $102 million, driven by higher domestic steel prices. EBITDA included idle expenses of $20 million for the Northshore and United Taconite mines. US iron ore […]
On Wednesday of this week the U.S. Department of Commerce reported Preliminary Census data on imports of foreign steel for the month of June 2016. The data is initially released in metric tons which Steel Market Update has converted to net tons for our readers. Imports in June totaled 2.630,373 net tons which are down […]
Flat rolled steel prices remained essentially unchanged for yet another week. We did pick up a break in the $600 barrier on hot rolled steel. However, we were only able to tie that price level to one Canadian mill into the Chicago market. The other mills appear to be holding much closer to $610-$620 per […]
Initial reports coming out of the financial community are suggesting ferrous scrap prices could be down $5 to $15 per ton once the August negotiations between the steel mills and their suppliers get under way. The expectation that the prime grades will be hit after spending a couple of months moving sideways. However, not all […]
For the week ending July 23, 2016, the American Iron & Steel Institute (AISI) estimated the U.S. steel industry produced 1,703,000 net tons of raw steel, a 2.5 percent decrease over the previous week and a 2.7 percent decrease over the same week one year ago. The estimated capacity utilization rate is 72.8 percent, down […]