International Steel Prices
US, offshore HR prices remain in step
Written by David Schollaert
October 23, 2024
US hot-rolled (HR) coil prices moved lower again this past week. A similar trend was seen in offshore markets, keeping domestic tags marginally above imports on a landed basis.
Since reaching parity with import prices in late August, stateside tags have been mostly stable. This has resulted in only negligible shifts in the US price premium.
SMU’s check of the market on Tuesday, Oct. 22, put average domestic HR tags at $685 per short ton (st), down $5/st from the week before. US hot band did rebound from July’s 20-month low, but prices have not shifted much. The average domestic hot band price is presently just $50/st above the recent bottom of $635/st in late July.
Domestic HR is now theoretically 5% more expensive than imported material. That’s just a touch higher than last week’s reading of 4.7%. While increases in the premium have been insignificant at times, prices are still up from late July, when stateside products were ~12% cheaper than imported HR.
In dollar-per-ton terms, US HR is now, on average, $34/st more expensive than offshore product (see Figure 1). That’s up $2/st vs. last week and up $106/st from late July when US tags were ~$72/st cheaper than offshore material.
The charts below compare HR prices in the US, Germany, Italy, and Asia. The left-hand side highlights prices over the last two years. The right-hand side zooms in to show more recent trends.
Methodology
This is how SMU calculates the theoretical spread between domestic HR coil prices (FOB domestic mills) and foreign HR coil prices (delivered to US ports): We compare SMU’s weekly US HR assessment to the CRU HR weekly indices for Germany, Italy, and East and Southeast Asian ports. This is only a theoretical calculation. Import costs can vary greatly, and that can influence the true market spread.
We add $90/st to all foreign prices as a rough means of accounting for freight costs, handling, and trader margin. This gives us an approximate CIF US ports price to compare to the SMU domestic HR coil price. Buyers should use our $90/st figure as a benchmark and adjust up or down based on their own shipping and handling costs. If you import steel and want to share your thoughts on these costs, please get in touch with the author at david@steelmarketupdate.com.
Asian HRC (East and Southeast Asian ports)
As of Wednesday, Oct. 23, the CRU Asian HRC price was $465/st, a $15/st decrease vs. the week prior. Adding a 25% tariff and $90/st in estimated import costs, the delivered price of Asian HRC to the US is approximately $672/st. As noted above, the latest SMU US HR price is $685/st on average.
The result: US-produced HR is theoretically $13/st more expensive than steel imported from Asia. Despite the week-over-week (w/w) increase, it is still quite removed from late December, when US HR was $281/st more expensive than Asian products.
Italian HRC
Italian HR prices inched $2/st higher this week to $549/st, according to CRU. After adding import costs, the delivered price of Italian HR is, in theory, $639/st.
That means domestic HR coil is now theoretically $46/st more expensive than imports from Italy. The spread is down $7/st w/w as US tags edged lower vs. a slight increase in Italian prices. Recall that US HR was $297/st more costly than Italian hot band just five months ago.
German HRC
CRU’s German HR price moved $4/st lower to $552/st this week. After adding import costs, the delivered price of German HR coil is, in theory, $642/st.
The result: Domestic HR is theoretically $43/st more expensive than HR imported from Germany, down $1/st w/w. Stateside hot band was at an $18/st discount just about a month ago. At points in 2023, in contrast, US HR was as much as $265/st more expensive than imported German hot band.
Notes: Freight is important when deciding whether to import foreign steel or buy from a domestic mill. Domestic prices are referenced as FOB the producing mill. Foreign prices are CIF, the port (Houston, NOLA, Savannah, Los Angeles, Camden, etc.). Inland freight, from either a domestic mill or from the port, can dramatically impact the competitiveness of both domestic and foreign steel. It’s also important to factor in lead times. In most markets, domestic steel will deliver more quickly than foreign steel. Effective Jan. 1, 2022, Section 232 tariffs no longer apply to most imports from the European Union. It has been replaced by a tariff rate quota (TRQ). Therefore, the German and Italian price comparisons in this analysis no longer include a 25% tariff. SMU still includes the 25% Section 232 tariff on prices from other countries. We do not include any antidumping (AD) or countervailing duties (CVD) in this analysis.
David Schollaert
Read more from David SchollaertLatest in International Steel Prices
US CR, import prices trend higher
The price spread between US-produced cold-rolled (CR) coil and offshore products remained largely flat in the week ended Nov. 8, on a landed basis.
CRU: China’s monthly steel exports reach highest level since 2015
China’s steel export volumes reached 11.2 million metric tons (mt) in October, the highest monthly level since September 2015. Steel export prices were mostly stable in China and India this week, while in Turkey steel export prices increased week over week (w/w).
Domestic and offshore HR prices trend toward parity
US hot-rolled (HR) coil prices moved lower this past week while tags in offshore markets were largely higher. Domestic tags are again nearly level with imports on a landed basis.
US CR prices decline, import tags stable
The price spread between US-produced cold-rolled (CR) coil and offshore products was negligibly tighter in the week ended Oct. 25, on a landed basis.