Steel Products

Domestic, offshore CRC prices steady
Written by David Schollaert
December 20, 2024
The price spread between US-produced cold-rolled (CR) coil and offshore products on a landed basis was unchanged in the week ended Dec. 20.
Domestic CR coil tags were flat week on week (w/w), as were offshore products, mirroring the same trend. As such, the stateside premium over imports remained flat.
US CR coil prices averaged $890 per short ton (st) in our check of the market on Tuesday, Dec. 17, flat vs. the prior week. Prices peaked at $1,325/st in January before falling nearly $450/st by summer. They have since fluctuated by roughly $25/st, slipping to a 15-month low of $885/st at the end of November.
Domestic CR prices are, theoretically, 17.1% more expensive than imports. This is unchanged vs. last week and still well removed from a 31.5% spread in early January.
In dollar-per-ton terms, US CR is still, on average, $122/st more expensive than offshore prices (see Figure 1). That’s flat w/w and off from a recent peak of $311/st in mid-January.
The charts below compare CR coil prices in the US, Germany, Italy, South Korea, and Japan. The left side shows prices over the last two years and the right side zooms in to highlight more recent trends.

Methodology
This is how SMU calculates the theoretical spread between domestic CR prices (FOB domestic mills) and foreign CR prices (delivered to US ports): We compare SMU’s US CR weekly index to the CRU CR weekly indices for Germany, Italy, and East Asia (Japan and South Korea). This is only a theoretical calculation. Import costs can vary greatly, influencing the true market spread.
We add $90/st to all foreign prices as a rough means of accounting for freight costs, handling, and trader margin. This gives us an approximate CIF US ports price to compare to the SMU domestic CR price. Buyers should use our $90/st figure as a benchmark and adjust up or down based on their own shipping and handling costs. (Editor’s note: If you import steel and want to share your thoughts on these costs, please get in touch with the author at david@steelmarketupdate.com.)
East Asian CR coil
As of Thursday, Dec. 19, the CRU Asian CR price was $526/st, unchanged w/w and ~$5/st lower than a month ago. Adding a 71% anti-dumping duty (Japan, theoretical) and $90/st in estimated import costs, the delivered price to the US is $990/st. The theoretical price of South Korean CR exports to the US is $616/st.
As noted above, the latest SMU CR price is unchanged at $890/st on average, placing US-produced CR theoretically $100/st below CR product imported from Japan but $274/st above CR imported from South Korea.


Italian CR coil
Italian CR prices were $645/st, flat this week. After adding import costs, the price of Italian CR delivered to the US is, in theory, $735/st.
That means domestic CR is still theoretically $155/st more expensive than CR coil imported from Italy. The spread is flat vs. last week but still ~$298/st below a recent high of $453/st mid-December.

German CR coil
CRU’s German CR price was sideways vs. the previous week. After adding import costs, the delivered price of German CR is, in theory, $731/st.
The result: Domestic CR is theoretically $159/st more expensive than CR imported from Germany. The spread unchanged w/w but well below a recent high of $428/st in the first week of 2024.

Notes: We reference domestic prices as FOB the producing mill, while foreign prices are CIF the port (Houston, NOLA, Savannah, Los Angeles, Camden, etc.). Inland freight from either a domestic mill or a port is important to keep in mind when deciding where to source from. It’s also important to factor in lead times. In most market cycles, domestic steel will deliver more quickly than foreign steel. Note also that, effective Jan. 1, 2022, the blanket 25% Section 232 tariff was removed from most imports from the European Union. It was replaced by a tariff rate quota (TRQ). Therefore, the German and Italian price comparisons in this analysis no longer include a 25% tariff.

David Schollaert
Read more from David SchollaertLatest in Steel Products

OCTG producers in Canada take aim at Mexico, US, others
Evraz NA and Welded Tube of Canada have lodged an unfair trade complaint against imports of OCTG, including those from USMCA trading partners Mexico and the US.

Final Thoughts
The difference: The spat with Turkey was a big deal for steel. This time, the 50% reciprocal tariff for Brazil – if it goes into effect as threatened on Aug.1 – hits everything from coffee and to pig iron. It seems almost custom-built to inflict as much pain as possible on Brazil.

CRU: US rebar and wire rod prices rise alongside S232 increase
CRU Senior Steel Analyst Alexandra Anderson discusses current market and pricing dynamics for long steel products in the US.
CRU: Excessive global supply could hit rebar mill investments in US
Following the onset of the war in Ukraine in March 2022, concerns about import availability and expectations of rising demand from President Biden’s Infrastructure Bill pushed US rebar prices to record highs. In response, a flurry of new mills and capacity expansions were announced to meet the rise in demand from growth in the construction […]

Steel buyer spirits tempered by soft spot market conditions
Steel sheet buyers report feeling bogged down by the ongoing stresses of stagnant demand, news fatigue, tariff negotiations or implementation timelines, and persistent macroeconomic uncertainty.