Steel Products

US HR price premium over imports narrows again
Written by David Schollaert
January 23, 2025
Hot-rolled (HR) coil prices were unchanged in the US this week, while tags abroad moved up. The result: US hot band margin over imports on a landed basis has narrowed further.
SMU’s average domestic HR price this week was $685 per short ton (st), flat vs. the week before. US hot band prices have recovered from a 20-month low of $635/st in late July. But prices have varied little since – averaging around $680/st.
Domestic HR is now theoretically 5% more expensive than imported material, down from 7.4% last week. Recall that US prices were ~12% cheaper than imports in late July.
In dollar-per-ton terms, US HR is now, on average, $34/st more expensive than offshore product (see Figure 1). Roughly $17/st lower vs. the prior week but still up about $106/st from late July – when US tags were ~$72/st cheaper than offshore material.
The charts below compare HR prices in the US, Germany, Italy, and Asia. The left side highlights prices over the last two years and the right side zooms in to show more recent trends.

Methodology
This is how SMU calculates the theoretical spread between domestic HR coil prices (FOB domestic mills) and foreign HR coil prices (delivered to US ports): We compare SMU’s weekly US HR assessment to the CRU HR weekly indices for Germany, Italy, and East and Southeast Asian ports. This is only a theoretical calculation. Import costs can vary greatly, influencing the true market spread.
We add $90/st to all foreign prices as a rough means of accounting for freight costs, handling, and trader margin. This gives us an approximate CIF US ports price to compare to the SMU domestic HR coil price. Buyers should use our $90/st figure as a benchmark and adjust up or down based on their own shipping and handling costs.
If you import steel and want to share your thoughts on these costs, please get in touch with the author at david@steelmarketupdate.com.
Asian HRC (East and Southeast Asian ports)
As of Thursday, Jan. 23, the CRU Asian HRC price was $445/st, up $10/st vs. the week prior. Adding a 25% tariff and $90/st in estimated import costs, the delivered price of Asian HRC to the US is ~$646/st. As noted above, the latest SMU US HR price is $685/st on average.
The result: Prices for US-produced HR are theoretically $39/st higher than steel imported from Asia – roughly $12/st lower week-over-week (w/w). The premium is still significantly lower than roughly a year ago when US HR was as much as $281/st more expensive than Asian products.

Italian HRC
Italian HR prices were $13/st higher this week at $560/st, according to CRU. After adding import costs, the delivered price of Italian HR is, in theory, $650/st.
That means domestic HR coil is theoretically $35/st more expensive than imports from Italy. With Italian and US tags trending in opposing directions, the spread is $13/st lower w/w. Recall that US HR was $297/st more costly than Italian hot band a year ago.

German HRC
CRU’s German HR price rose $25/st to $542/st this week. After adding import costs, the delivered price of German HR coil is, in theory, $657/st.
The result: Domestic HR is theoretically $28/st more expensive than HR imported from Germany, down $25/st from last week. Stateside hot band was at an $18/st discount about four months ago. At points in 2023, in contrast, US HR was as much as $265/st more expensive than imported German hot band.

Notes: Freight is important when deciding whether to import foreign steel or buy from a domestic mill. Domestic prices are referenced as FOB the producing mill. Foreign prices are CIF, the port (Houston, NOLA, Savannah, Los Angeles, Camden, etc.). Inland freight, from either a domestic mill or from the port, can dramatically impact the competitiveness of both domestic and foreign steel. It’s also important to factor in lead times. In most markets, domestic steel will deliver more quickly than foreign steel. Effective Jan. 1, 2022, Section 232 tariffs no longer apply to most imports from the European Union. It has been replaced by a tariff rate quota (TRQ). Therefore, the German and Italian price comparisons in this analysis no longer include a 25% tariff. SMU still includes the 25% Section 232 tariff on prices from other countries. We do not include any antidumping (AD) or countervailing duties (CVD) in this analysis.

David Schollaert
Read more from David SchollaertLatest in Steel Products

U.S. Steel to halt slab conversion at Granite City Works
U.S. Steel said it plans to reduce slab consumption at its Granite City Works near St. Louis, a company spokesperson said on Monday. The Pittsburgh-based steelmaker will shift the production and processing of steel slabs to its Mon Valley Works near Pittsburgh and its Gary Works near Chicago. Citing a United Steelworkers (USW) union memo, […]

SMU Week in Review: September 1-5
Here are highlights of what’s happened this past week and a few upcoming things to keep an eye on.

HR Futures: Market finds footing on supply-side mechanics
As Labor Day marks the transition into fall, the steel market enters September with a similar sense of change. Supply-side fundamentals are beginning to show signs of restraint: imports are limited, outages loom, and production is capped, setting the stage for a market that feels steady on the surface but still unsettled underneath.

Beige Book: US markets remain cautious amidst volatile pricing environment
Sluggish economic activity across the US was largely attributed to uncertainty caused by tariff policies and growing cost pressures, according to the US Federal Reserve’s (The Fed) latest Beige Book report. The Fed’s latest economic report, posted on Sept. 3, consists of economic findings from the six weeks preceding Aug. 25 throughout 12 districts. Economic […]

Rig count dips again in both US and Canada
Oil and gas drilling activity waned in the US and Canada this past week. Ticking own for the second straight week in both regions.