Weekly raw steel production by U.S. mills totaled 1,561,000 net tons in the week ending Nov. 28, while the average operating rate was 70.6 percent. Production declined by 1.3 percent from the week prior, likely due to the holiday break. Present capacity utilization represents a 14.4 percent decrease from the same period last year when […]
Weekly raw steel production by U.S. mills totaled 1,582,000 net tons in the week ending Nov. 21. The operating rate was a fraction higher than the prior week at 71.5 percent. Despite the steady increase in production through much of 2020, the latest week’s output remains 13.2 percent behind the same week last year when the […]
Kevin Dempsey, Interim President and Chief Executive Officer of the American Iron and Steel Institute, is confident the industry trade association will be able to work productively with the incoming Biden administration in pursuit of the steel industry’s goals. “Obviously there will be a change in personality and personnel in key positions, but at the […]
Raw steel production by U.S. mills increased by 7,000 net tons last week. In the week ending Nov. 14, domestic steel production totaled 1,580,000 net tons, pushing the average industry capacity utilization rate up slightly to 71.4 percent. Although production continues on a slow upward trajectory, it remains 13.3 percent below the same week last year when the operating rate was […]
Editor’s note 11/17/20: The data in the “Supply Tons YTD” column on Table 3 didn’t populate correctly, and therefore, was in error. Table 3 has now been updated accordingly. Mill shipments and supply of sheet products continue to see slight yet steady growth since reaching bottom in June. This analysis is based on steel mill […]
U.S. raw steel production remained steady in September, up 0.8 percent to 6,587,000 net tons, as reported by the American Iron and Steel Institute. AISI’s monthly raw steel production estimates are different than the weekly estimates SMU reports each Tuesday; the monthly estimates are based on over 75 percent of the domestic mills reporting versus […]
U.S. apparent steel supply remained flat from August to September, up 0.4 percent to 7.19 million net tons, according to the latest U.S. Department of Commerce and American Iron and Steel Institute data. While supply levels have improved each month since May, recall that April and May were the two lowest levels seen in the […]
U.S. steel mills shipped 6,662,904 net tons in September, a 2.0 percent increase from the 6,532,652 net tons shipped in the previous month, but a 14.2 percent decrease from the 7,767,310 net tons shipped in September 2019, reported the American Iron and Steel Institute. Shipments year-to-date totaled 60,449,359 net tons, a 16.7 percent decrease vs. […]
Weekly raw steel production by U.S. mills continues to climb, a trend that started back in May. In the week ending Nov. 7, raw steel production totaled 1,573,000 net tons. The capacity utilization rate rose to 71.1 percent, up from 70.0 percent the week prior. Despite the steady rise in output, the current week’s production represents […]
Domestic mills continue to increase steel production as the economy rebounds from the coronavirus, with the capacity utilization rate topping 70 percent again for the first time since late-March. In the week ending Oct. 31, raw steel production totaled 1,557,000 net tons, at a mill operating rate of 70.4 percent, up from 69.7 percent the […]
Editor’s note 11/3/20: Some of the data as originally published in Table 1 was incorrect due to a spreadsheet error (specifically the change in shipments 3M Y/Y column). The table has been updated with the correct information below. Mill shipments and supply of sheet products have turned, albeit slightly, since reaching bottom in […]
Weekly raw steel production by U.S. mills rose again by 0.5 percent to 1,542,000 net tons in the week ending Oct. 24. The mill operating rate hit 69.7 percent, up from 69.4 percent the week prior. Despite the steady increases over the past 20 weeks as the economy recovers from COVID, domestic steel production was still […]
Raw steel production by U.S. mills rose again by 2.2 percent to 1,535,000 net tons in the week ending Oct. 17, continuing an uptrend that began nearly five months ago. The mill operating rate hit 69.4 percent, up from 67.9 percent the week prior. Despite the repeated rise in capacity utilization, production was still down by 15.0 percent […]
By CRU Analyst Estelle Tran, from CRU’s Global Steel Trade Service The spike in sheet purchasing activity pushed prices up $200 /s.ton over the last two months and mill lead times for HR coil over six weeks. Steel Market Update, which is owned by CRU, also reported CR and HDG coil lead times in the […]
Raw steel production by U.S. mills rose another 1.2 percent in the week ending Oct. 10 to 1,502,000 net tons, the 16th increase in the last 18 weeks. The operating rate reached 67.9 percent last week, up from 66.6 percent the week prior. Even though production has experienced steady increases, mill output was still 16.8 percent below levels of […]
U.S. apparent steel supply continued it’s recovery in August, up 2.6 percent from July to 7.17 million net tons, according to the latest U.S. Department of Commerce and American Iron and Steel Institute data. While supply levels have improved each month since May, recall that April and May were the two lowest levels seen in […]
U.S. raw steel production rose 9.4 percent to 6,538,000 net tons in August, as reported by the American Iron and Steel Institute in Washington. August production is slightly below the 2020 monthly average of 6,580,000 tons, and down 19.8 percent compared to the same month last year. August production was 560,000 tons higher than July, […]
Steel imports declined by more than 20 percent in the first nine months of 2020, including a nearly 27 percent drop in finished steel imports, reports the American Iron and Steel Institute. The estimated finished steel import market share for the year to date is 18 percent, down from 19 percent in full-year 2019. Including […]
Raw steel production by U.S. mills increased 0.3 percent in the week ending Oct. 3 to 1,484,000 net tons, another small sign of rising steel demand. The operating rate of 66.6 percent was up from 66.1 percent the week prior. Although domestic production has seen steady gains since April, last week’s output was still 17.7 percent […]
Raw steel production by U.S. mills jumped by 2.4 percent in the week ending Sept. 26 to 1,480,000 net tons, following a small dip in the previous week. The operating rate last week hit 66.1 percent, up from 64.5 percent in the prior week. The last time production topped 66 percent of the mills’ capability was 25 […]
U.S apparent steel supply remained flat from June to July, up 0.8 percent to 6.98 million net tons, according to the latest U.S. Department of Commerce and American Iron and Steel Institute data. While June and July supply levels have both shown improvement, recall that April and May were the two lowest levels seen in […]
Domestic steel production dipped a bit last week for only the second time in the last 15 weeks. Production by U.S. mills totaled 1,446,000 net tons in the week ending Sept. 19, with the mills operating at an average utilization rate of 64.5 percent. Production in the Sept. 19 week was down 0.9 percent from the prior […]
By CRU Prices Analyst Estelle Tran, from CRU’s Global Steel Trade Service A combination of increased seasonal demand, low service center inventories, unplanned outages, spike in scrap prices and government restrictions on Brazilian slab imports have added fuel to the usual seasonal uptick and turned it into a surge. After reaching a bottom in mid-August, […]
Domestic steelmakers continued to dial up production last week, with raw steel output rising for the 13th time in the past 14 weeks. Production by U.S. mills totaled 1,459,000 net tons in the week ending Sept. 12, with the mills at an average utilization rate of 65.1 percent. Production in the Sept. 12 week was up […]
Steel import permit applications for August totaled 1,394,000 net tons—a 30.5 percent decrease from the 2,006,000 permit tons recorded in July and a 48.4 percent decrease from the July final imports total of 2,703,000, reported the American Iron and Steel Institute, based on the Commerce Department’s most recent Steel Import Monitoring and Analysis (SIMA) data. […]
After a brief pause in late August, raw steel production resumed its upward trajectory, rising again for the 12th time in the past 13 weeks. Raw steel output by U.S. mills totaled 1,428,000 net tons in the week ending Sept. 5, with the mills at an average utilization rate of 63.7 percent. Production in the […]
The Trump administration has announced a tightening of Brazil’s steel quota that will sharply reduce the tonnage of steel slabs imported into the U.S. for the rest of the year. “In light of recent deterioration in market conditions brought on by the COVID-19 pandemic affecting domestic steel producers, the United States has deemed it necessary […]
After 11 straight weeks of increased steel production, raw steel output and mill capability utilization took a slight step backward last week. Raw steel output by U.S. mills totaled 1,383,000 net tons in the week ending Aug. 29, with the mills at an average utilization rate of 61.7 percent. Production in the Aug. 29 week was down […]
For the 11th week in a row, domestic steelmakers continued to dial up their production–a sign of improving steel demand. Raw steel output by U.S. mills totaled 1,412,000 net tons in the week ending Aug. 22, with the mills hitting an average utilization rate of 63.0 percent, reported the American Iron and Steel Institute. That’s a […]
By CRU Prices Analyst Estelle Tran, from CRU’s Global Steel Trade Service U.S. sheet steel prices hit their lowest point of the year on Aug. 12 and are slated to rise as steel consumption has been increasing. Steel mill capacity utilization reached 61.5 percent in the week ended Aug. 15, up from 60.4 percent the […]