U.S. steel exports in September totaled 584,858 net tons (530,575 metric tons), down 9.6 percent from August and down 35.3 percent from September 2017. Surpassing August’s low, this is now the lowest total monthly export figure seen since December 2002 when 527,659 tons were shipped out of the country. Prior to the last three months, […]
Total rolled product imports declined by 20.4 percent in October, versus the same month last year, measured as a three-month moving average, but the effects of Section 232 are still not clear. This early look at October’s import volume is based on Commerce Department license data (see explanation below). Figure 1 shows the tonnage of […]
Flat rolled steel prices continue to vacillate as we saw the low end of our range on benchmark hot rolled coil improve by $20 per ton. We are aware of a couple end-of-the-year deals that are below our range, but we feel at this point they are limited and not available to the greater market. […]
Domestic steelmakers achieved their highest production rate in a decade last week, hitting a capability utilization of 81.8 percent. The last time production was higher was the week ending Sept. 27, 2008, when the mills operated at 83.2 percent and produced nearly 2 million tons. U.S. raw steel production for the week ending Nov. 3 […]
U.S. steel imports for October are likely to fall just below 3 million tons when the Census data is final, based on license data from the Department of Commerce. The total is roughly in line with the 12-month moving average for imports, but up more than 30 percent from September. Imports of semi-finished steel, mostly […]
Flat rolled steel prices have stalled, despite the increase announcements out of many of the domestic steel mills. Plate steel spot prices, on the other hand, continue to remain firm in December with an expectation of a $40 price increase being collected in January. Steel Market Update canvassed the flat rolled and plate steel buyers […]
The price increase on flat rolled seems to have “fizzled out,” according to many of the steel buyers Steel Market Update spoke with over the past two days. A number of mills have sweetened their end-of-the-year deals in order to finish out their 2018 order book. This is not unusual during a normal fourth quarter, […]
Domestic steel mills achieved a production rate last week not seen in more than six years. U.S. raw steel production for the week ending Oct. 27 totaled 1,898,000 net tons with the mills averaging 81.0 percent of their capability, up from 80.0 percent reported the prior week, according to the American Iron and Steel Institute. […]
The following article was contributed by CRU North America Steel Analyst Ryan McKinley The trade dispute between the United States and Canada has caused inventories to build and put downward pressure on prices. The 25 percent duties on steel imports in place by Canada and the U.S. against one another is eroding profits and driving […]
As expected in a market where foreign suppliers must pay a 25 percent tariff (50 percent for those in Turkey), steel imports into the United States are down 11 percent for the year to date. Unexpected were the increases in imports of hot rolled sheet and plate. Steel Market Update’s analysis of Commerce Department data […]
The U.S. Department of Commerce released updated foreign steel import data for September and October yesterday, with the September figure down to 2.2 million tons and the October trend remaining over 3 million tons. Prior to this week, the September total was hovering around 2.7 million to 2.9 million net tons. Our October trend is […]
Flat rolled steel buyers are advising Steel Market Update that lead times have extended about one week since the recent price announcements. The mills continue to ask about their competition and to negotiate, which is not a sure-fire sign of strength or conviction in the new increases. Plate is a different animal and continues to […]
U.S. mills have operated at 80 percent of capacity or better for two weeks in a row. U.S. raw steel production for the week ending Oct. 20 totaled 1,875,000 net tons with the mills averaging 80.0 percent of their capability, down slightly from 80.2 percent reported the prior week, according to the American Iron and […]
Table 1 summarizes the October prices of the five materials considered in this report and the month/month, three months/three months and year/year change. Price changes have been mixed. In the last three months, coking coal and iron ore have trended up as pig iron, scrap and zinc have trended down. This was the same pattern […]
In the last 12 months, the price of coking coal and scrap have continuously trended up, zinc has continuously trended down, and iron ore and pig iron have been erratic. Table 1 summarizes the price changes through November of the five materials considered in this Steel Market Update report. It includes the month/month, 3 months/3 […]
Cleveland Cliffs CEO Lourenco Goncalves is looking forward to the completion of the company’s HBI pellet plant in Toledo, Ohio. The project is on time and under budget and construction has begun on the 400-foot tower that will be completed by the end of 2019. Startup of HBI production is anticipated in mid-2020. The company […]
They may be off the table as of today, but late last week (and some buyers reported some still existing early this week) there were special deals – many tied to large tonnage – as the domestic mills attempted to fill their hot rolled order books. We did have a number of buyers and a […]
The flat rolled mills announced a price hike last week. This was at the same time Steel Market Update sources were advising of $38.00/cwt ($760 per ton) out of more than one domestic steel mill. The increase, announced initially by Nucor, was seen as an attempt to dry up the sub-$800 offers and put a […]
U.S. raw steel production for the week ending Oct. 13 totaled 1,881,000 net tons with the mills operating at 80.2 percent of capacity, reported the American Iron and Steel Institute. The current week’s production is a 1.6 percent improvement from the prior week, and a 10.3 percent jump from the same period last year, when […]
Earlier today, the U.S. Department of Commerce released the latest foreign steel import license data for September and October. Based on our analysis, the import trend for October continues to be much higher than we would have anticipated. We are looking at the month trending over 3 million net tons. The biggest reason for the […]
Apparent steel supply remained high in August, coming in at 9,828,339 net tons, according to government data released late last week. This is the third highest level of the year, just a hair under the April figure (9,829,298 tons), and both being about 100,000 tons under the March high (9,935,479 tons). Apparent steel supply is […]
Imports of other metallic coated sheet have declined in all regions in 2018. Each month, Steel Market Update produces an import analysis by region for two of the six flat rolled product groups (HRC, CRC, HDG, OMC, CTL plate and coiled plate). This month, the focus is on coated products. The intent of these regional […]
The Great Lakes region has received the greatest volume of hot-dipped galvanized sheet imports so far in 2018. Each month, Steel Market Update produces an import analysis by region for two of the six flat rolled product groups (HRC, CRC, HDG, OMC, CTL plate and coiled plate). This month, the focus is on coated products. […]
Yesterday, Nucor announced a $40 per ton ($2.00/cwt) price increase on all flat rolled products they produce. The increase was to take effect immediately on all “spot” orders. On paper, the increase announcement does not impact contract pricing. However, steel buyers are advising Steel Market Update that the reason behind the Nucor announcement was two-fold: […]
U.S. steel exports in August totaled 646,692 net tons (586,670 metric tons), down 1.4 percent over July and down 29.5 percent from August 2017. Surpassing July’s low, this is now the lowest total export figure seen since May 2009 when 627,968 tons were shipped out of the country. Prior to July and August levels, total […]
We saw mixed results in the flat rolled markets this week. Benchmark hot rolled dropped $5 per ton compared to one week ago. Cold rolled was modestly higher ($5/ton), while galvanized and Galvalume were down $15 per ton. Plate prices remained intact with no change compared to one week ago. Here is how we see […]
Spot plate prices have not budged this week, according to the numerous data points received from both large and small plate buyers today. Our range is $980 to $1,030 per ton delivered with an average of $1,005 per ton. The domestic plate mills continue to be on “controlled order entry” (they don’t like the word […]
U.S. mills have cranked out steel at a capability utilization rate of 79.0 percent or better for nine weeks in a row, but only briefly have breached the 80 percent mark. U.S. raw steel production for the week ending Oct. 6 totaled 1,851,000 net tons with the mills operating at 79.0 percent capacity, reported the American […]
The U.S. Department of Commerce released Final Census Data on August foreign steel imports late last week. The final data shows August imports hit 3,034,752 net tons, just slightly above the 2,987,565 net tons reported for the month of July. Total imports continue to be resilient, mostly on the back of semi-finished steels (mostly slabs […]
Rolled product imports into the United States were down by 21.6 percent in September on a three-month moving average basis compared with the prior year, according to Steel Market Update’s latest analysis of import license data. Figure 1 shows the tonnage of total rolled steel and semi-finished imports through September on a 3MMA basis. The […]