Mill capacity utilization increased by a percentage point in the week ending Dec. 14 to 79.7 percent. Production totaled 1,844,000 net tons, up 1.3 percent from the previous week but down 0.9 percent compared with the same week last year, reported the American Iron and Steel Institute. Adjusted year-to-date production through Dec. 14 totaled 92,584,000 net […]
On Friday afternoon of this past week, ArcelorMittal USA began advising their flat rolled clients of their intention to raise sheet prices by $40 per ton. AMUSA customers were advised by phone and by email that base prices of hot rolled, cold rolled and coated products would increase effective immediately. At the same time, AMUSA […]
After declining for much of 2019, steel prices have moved up substantially in the last two months. Will the trend continue into 2020? Flat rolled steel producers raised prices three times during October and November for a total of $110 per ton. (Editor’s note: ArcelorMittal USA announced an additional $40 flat rolled increase on Friday. […]
U.S. raw steel production in October rose 3.5 percent to 7,991,393 net tons, reported the American Iron and Steel Institute in Washington. October production is slightly below the 2019 average of 8,088,957 tons and down 4.1 percent compared to the same month last year. Broken down by production method, 5,657,855 tons (70.8 percent) were produced […]
Steel Market Update offers a comprehensive series of import reports ranging from the first look at licensed data to the very detailed look at volume by district of entry and source nation. The report you are reading now is designed to plug the gap between those two. National level import reports do a good job […]
Steel Market Update offers a comprehensive series of import reports ranging from the first look at licensed data to the very detailed look at volume by district of entry and source nation. The report you are reading now is designed to plug the gap between those two. National level import reports do a good job […]
Steel Market Update offers a comprehensive series of import reports ranging from the first look at licensed data to the very detailed look at volume by district of entry and source nation. The report you are reading now is designed to plug the gap between those two. National level import reports do a good job […]
Steel Market Update offers a comprehensive series of import reports ranging from the first look at licensed data to the very detailed look at volume by district of entry and source nation. The report you are reading now is designed to plug the gap between those two. National level import reports do a good job […]
Steel Market Update offers a comprehensive series of import reports ranging from the first look at licensed data to the very detailed look at volume by district of entry and source nation. The report you are reading now is designed to plug the gap between those two. National level import reports do a good job […]
Steel Market Update offers a comprehensive series of import reports ranging from the first look at licensed data to the very detailed look at volume by district of entry and source nation. The report you are reading now is designed to plug the gap between those two. National level import reports do a good job […]
The domestic plate steel mills have made three price increase announcements totaling $130 per ton ($6.50/cwt). The lead times out of the plate mills have moved into February. Scrap has been moving higher and is expected to move higher over the winter months. The mills are beginning to see some traction in plate pricing. Steel […]
California Steel Industries informed customers Wednesday that, “due to changing market conditions,” it has increased transaction prices for its products by $70 per ton. The change applies immediately to new orders of hot rolled, P&O, cold rolled and galvanized products. “All pricing is subject to slab availability and mill capacity,” the company said in its […]
This Steel Market Update report examines the import share of sheet, plate, long and tubular products and 16 subcategories. Since January, there has only been one month when the import market share of total sheet products exceeded 15 percent. The import share of HRC has been below 10 percent since January. The most striking result […]
October apparent steel supply remained steady at 8.7 million net tons, according to data from the American Iron and Steel Institute and U.S. Department of Commerce. October supply is the second lowest level seen in the last 23 months, with the lowest occuring the month prior. Apparent steel supply, a proxy for demand, is determined […]
Flat rolled steel prices increased by $15 per ton or more in the past week, depending on the product, while plate prices rose by $10 per ton, as the mills continued trying to collect their recent price increases. Price momentum is pointing to likely higher prices in the weeks to come as the mills try […]
Raw steel output by U.S. mills declined again in the week ending Dec. 7. Production totaled 1,821,000 net tons at a capability utilization rate of 78.7 percent, down 0.8 percent from the previous week and down 2.1 percent compared with the same week last year when utilization was at 79.4 percent, reported the American Iron and […]
By CRU Senior Analyst Erik Hedborg, from CRU’s Steelmaking Raw Materials Monitor Throughout 2019, steelmakers’ willingness to pay higher prices for premium quality steelmaking raw materials has diminished. For iron ore, the spread between 65% and 62% Fe fines has fallen to $8 /t in Q4, well below the $28 /t peak in 2018 Q3. […]
Total steel imports into the United States are trending toward 2.5 million tons in December, which would be up dramatically over November and higher than the 12-month average. However, imports of semifinished steels, some of which are subject to quota restrictions, are likely to come in well under the current trend of 1.1 million tons. […]
The U.S. exported 709,496 tons of steel in October, according to final Census data, a 15 percent increase from September and up 12 percent from the same month one year ago. October exports were 13 percent above the 2019 average of 625,236 tons, but remain significantly muted compared to recent years. As shown in the […]
The mills have succeeded in collecting a portion of their recent price increases, but how much and for how long? Steel Market Update canvassed buyers this week and opinions varied widely. Flat rolled producers raised prices by a total of $110 per ton in three rounds of announcements during October and November. Steel Market Update […]
SSAB Americas notified customers on Friday, Dec. 6, that it is increasing transaction prices by a minimum of $50 per ton effective immediately for all new non-contract orders. Other mills are expected to follow. SSAB’s increase applies to As-Rolled Mill Plate, Cut-To-Length Plate >72”, Hot Rolled Coils >72”, as well as Normalized Plate and Quenched […]
By CRU Principal Analyst James Campbell, from CRU’s Long Products Monitor Steel longs prices have changed direction this month with rises now observed in many markets. Although underlying demand has improved in some regions it is still weak elsewhere. Buyers in many regions have restocked in the last month while producers exposed to scrap and […]
In the last month, the prices of three of the five raw materials tracked by Steel Market Update in this report declined, one advanced and one was unchanged. Table 1 summarizes the price changes through Nov. 20 of the five materials considered in this analysis. It reports the month/month, 3 months/3 months and 12 months/12 […]
November’s licensed import volume of total rolled steel products was the lowest since February 2010. Year over year, total rolled product imports in November were down by 27.4 percent on a three-month moving average (3MMA) basis. This follows the 17.7 percent decrease in October and 15.5 percent decline in September on the same basis. This […]
Benchmark hot rolled coil rose this week as we saw the lower end of the range move much higher compared to what we collected last week. We found most data points on HRC between $540-$570. We continue to see high base price spreads between hot rolled and cold rolled/coated steels. Cold rolled, with its $175 […]
Raw steel output by U.S. mills dipped again in the week ending Nov. 30, inching below the 80 percent mark for the first time since the week ending Oct. 19. Production totaled 1,835,000 net tons at a capability utilization rate of 79.3 percent, down 1.4 percent from the previous week and down 3.6 percent compared […]
By CRU Senior Analyst Dmitry Popov, from CRU’s Iron Ore Market Outlook After two weeks of increases, iron ore prices moved marginally lower this week by $1 /t w/w as CRU has assessed the 62% Fe fines price at $89 /t, CFR China. The end of the upward momentum in iron ore prices was primarily […]
Last week U.S. Steel and ArcelorMittal USA announced a third round of price increases. This week Nucor and Algoma followed suit. Not every mill has followed their lead, however. As a result, there are still some holes out there. Where, why and from whom are the questions of the day, which we can’t answer at […]
Nucor’s Sheet Mill Group and Canada’s Algoma Steel have matched last week’s price increases by U.S. Steel and ArcelorMittal USA. Nucor informed customers on Monday that is has increased based prices on new orders of hot rolled, cold rolled and galvanized steel by a minimum of $30 per ton ($1.50/cwt). LIkewise, Algoma notified its flat […]
Nucor’s Plate Mill Group informed customers on Monday that it is raising prices on carbon and alloy plate and on heat-treated plate by a minimum of $40 per ton. The increase is effective on new orders accepted for January production. Nucor’s move follows on SSAB’s announcement on Friday that it was increasing transaction prices for […]